產品精準搜尋

產品介紹

模組化電源供應器
  • Facebook
  • LINE
  • Twitter
  • LinkedIn
AMETEK 1000W DC high power supply Module for the ReFlex Power | 洛克Lockinc
AMETEK 1000W DC high power supply Module for the ReFlex Power | 洛克Lockinc
功能說明

Product Overview

ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.

Up to 8 mainframes, potentially up to 95 modules, can be controlled via a single controller. The controller communicates to the individual modules via a high speed proprietary bus protocol, providing very high data rates and a high degree of deterministic control. The RFP™ controller communicates to the host controller via an Ethernet LAN connection designed to be compliant with the LAN Extension for Instrumentation ( ™ ) standard, assuring interoperability and ease of integration. RFP™ system modules can be combined via the controller, permitting the creation of “virtual assets” with the voltage/current combinations required for a particular test regime. Creating “virtual assets” reduces the “logistical tail” and total cost of ownership.

Available power modules include 
  • Single slot, 330 Watt programmable DC supplies
    • 16V, 20.6A
    • 65V, 5.1A
       
  • Dual slot, 1kW programmable DC supplies
    • 33V, 30A
    • 50V, 20A
    • 50V, 25A
    • 120V, 8.3A
    • 450V, 2.3
       
  • Triple slot, 875 VA, single phase, programmable AC supply
    • Dual range: 280V(rms), 3.5A(rms)
    • Dual Range: 140V(rms), 7A(rms)
       
  • Triple slot, 500V, programmable electronic DC loads
    • 15A, 375 Watt
    • 30A, 750 Watt

The mainframe provides internal power distribution, cabling, I/O and power connection and rack mounting for 12-asset slots. The mainframe also supplies the signal and control bus fabric supporting multi-module series/parallel operation, complex triggering, fault I/O and inter-mainframe control infrastructure.

DC High Power Modules General Specifications
Line Regulation +\- 10% line change
Steady State, 
Voltage Mode		 0.01% of full-scale + 10mV (330W) and 
0.03% of full-scale (1kW)
Steady State, 
Current Mode		 0.05% of fullscale (330W) and 0.1% of full-scale (1kW)
Transient, Voltage Mode Less than 1% of full-scale excursion returning to steady state within 500 micro-sec
Transient, Current Mode Less than 0.05% of full-scale (330W) and less 
than 0.1% (1kW)
Remote Sense Up to 3V load line drop. The drop in the load leads subtracts from the maximum voltage available for the load.
Parallel Up to six like modules
Series Up to five like modules for 16V, 65V; 
up to three like models for 33V, 50V, 120V
Float not to exceed 200V (16V, 33V, 50V 120V), 300V (65V), 450V (450V).
Sag/Surge/Hold Up Sag to 65% of nominal for 450ms at full output power with AC input at ≥200VAC. Surge to 135% of nominal for 450ms at full output with AC input ≤230VAC. 10ms hold up at loss of input.
Remote programming connector 9-pin D-sub
Output connector Combination signal/power contact subminiature D (Mating connector kit available)
Physical 330W: 4.2 lbs (1.91 Kilograms)
1000W: 8.7 lbs (3.95 Kilograms)
Regulatory
 		 Certified to UL 61010-1, CSA C22.2 No.
61010.1 and IEC/EN 61010-1.
Compliance with EN61326 and FCC 21 CFR,
Subpart J
CE Mark is to EMC and LVD
All specifications: 25°±5°C.
Output Voltage and Current
Output Voltage 33V 450V 50V 50V 120V
Output Current 30A 2.3A 20A 25A* 8.3A
Maximum Power 990W 1035W 1000W 1250W* 996W
Mainframe Slots 2 2 2 2 2
Output rise / fall time 20msec 20msec 20msec 20msec 20msec
Ripple / Noise
RMS 15mV 40mV 20mV 20mV 20mV
Peak-Peak 60mV 200mV 75mV 75mV 75mV
Programming Accuracy
Voltage (0.05% of setpoint +) 16.5mV 225mV 25mV 25mV 60mV
Current (0.2% of setpoint +) 30mA 2.3mA 20mA 25mA 8.3mA
Temperature Coeffcient
Voltage /˚C 3.3mV 45mV 5mV 5mV 12mV
Current /˚C 7.5mA 0.6mA 7.5mA 7.5mA 2.5mA
*1250 Watt module must have an AC input voltage above 188 Vac or DC input above 210 vDC. The module will not operate below the required input line voltage.
All specifications are subject to change

Manuals
ReFlex Power Operation Manual Rev K - 11/9/2011 (3.64MB)
ReFlex Power Programming Manual Rev J - 11/9/2011 (1.76MB)
Tech Note: Mating Connnectors for Mainframe Rev E - 02/07/09 - 186Kb
Tech Note: Mating Connnectors for Controller Rev F - 02/07/09 - 146Kb
Tech Note: Mating Connnectors for LPDC 16V Rev E - 02/07/09 - 158Kb
Tech Note: Mating Connnectors for LPDC 65V Rev E - 02/07/09 - 153Kb
Tech Note: Mating Connnectors for HPDC 33V / 50V Rev F - 02/07/09 - 94Kb
Tech Note: Mating Connnectors for HPDC 120V Rev X2 - 03/31/09 - 92Kb
Tech Note: Mating Connnectors for HPDC 450V Rev E - 02/07/09 - 108Kb
Tech Note: Mating Connnectors for FPDC Rev E - 02/07/09 - 87Kb
Tech Note: Mating Connnectors for AC Rev D - 02/07/09 - 158Kb
Tech Note: Mating Connnectors for Loads Rev D - 02/07/09 - 99Kb
Tech Note: Fault Protection Groups Rev A - 02/07/09 - 96Kb
Tech Note: Firmware Updates Rev B - 02/07/09 - 421Kb
Quick Reference guide : Reflex Power Network Communication and Output Connections Rev E - 5/6/2010 (244KB)
Data Sheet
ReFlex Power Data Sheet 3/30/2012 (541KB)
Software
AC IVI-COM Driver (2.0.11.0) ¹ 4380277-09 3/26/2012_2.76 Mb
DC IVI-COM Driver (2.0.12.0) ¹ 4380276-10 3/26/2012  3.26 Mb
Loads IVI-COM Driver (2.0.9.0) ¹ 4380278-07 3/26/2012_2.68 Mb
Firmware Update Executable 21.2 Kb
Firmware Update V3.500 2/16/2012 (2.25MB)
ReFlex Power Control & Monitor GUI
- ElgarRAC v2.0.5.0 
- ElgarRDC v2.0.6.0 
- ElgarRLD v2.0.5.0		 02/16/2010 - V1.0.0.2 - 33.7Mb
Loading...
與我們聯絡