產品介紹

模組化電源供應器
  • Facebook
  • LINE
  • Twitter
  • LinkedIn
AMETEK Power AC Power Module - ELGAR ReFlex  875VA AC Power Source Module  | 洛克Lockinc
功能說明

Product Overview

ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.

Up to 8 mainframes, potentially up to 95 modules, can be controlled via a single controller. The controller communicates to the individual modules via a high speed proprietary bus protocol, providing very high data rates and a high degree of deterministic control. The RFP™ controller communicates to the host controller via an Ethernet LAN connection designed to be compliant with the LAN Extension for Instrumentation ( ™ ) standard, assuring interoperability and ease of integration. RFP™ system modules can be combined via the controller, permitting the creation of “virtual assets” with the voltage/current combinations required for a particular test regime. Creating “virtual assets” reduces the “logistical tail” and total cost of ownership.

Available power modules include 
  • Single slot, 330 Watt programmable DC supplies
    • 16V, 20.6A
    • 65V, 5.1A
       
  • Dual slot, 1kW programmable DC supplies
    • 33V, 30A
    • 50V, 20A
    • 50V, 25A
    • 120V, 8.3A
    • 450V, 2.3
       
  • Triple slot, 875 VA, single phase, programmable AC supply
    • Dual range: 280V(rms), 3.5A(rms)
    • Dual Range: 140V(rms), 7A(rms)
       
  • Triple slot, 500V, programmable electronic DC loads
    • 15A, 375 Watt
    • 30A, 750 Watt

The mainframe provides internal power distribution, cabling, I/O and power connection and rack mounting for 12-asset slots. The mainframe also supplies the signal and control bus fabric supporting multi-module series/parallel operation, complex triggering, fault I/O and inter-mainframe control infrastructure.

AC Power Modules General Specifications
Current, Maximum 140V Range 7A, not to exceed 875 VA, Overload 10A
for 0.5 Seconds
Current, Maximum 280V Range 3.5A, not to exceed 875 VA, Overload 5A
for 0.5 Seconds
Frequency 45-1200 Hz, up to 5 kHz optional
Crest Factor 4.8 X FS rms current
Load Regulation 100% Resistive Load effect (<100 msec)
Voltage Mode 0.5% of FS
Current Mode 0.1% of FS
Line Regulation 10% Line effect (< 100ms)
Voltage Mode 0.1% of FS
Current Mode 0.1% of FS
Programming Accuracy Voltage 0.1% of FS + .2%/kHz
Current +/-(0.5% + 0.75%/kHz) of full-scale
Frequency 0.01% of setpoint
Programming Resolution Voltage 0-140VAC 9mV, 0-280 18mV
Current 2.2mA
Frequency 0.1Hz thru 1kHz; 0.5Hz thru 5KHz
Temperature coefficient Voltage .05% of FS per °C
Current .05% of FS per °C
Distortion <1% to 500Hz
<2% to 2KHz
<5% to 5KHz
Output DC Offset ±0.1Vdc maximum
Efficiency 72%
RMS Noise 55dB below full-scale Input (via RFP Mainframe)
Inrush Current 8.8A at 115Vac; 17.6A at 230Vac
14.6A at 270Vdc
Power Factor 0.95 typical
Hold-up time 10ms
Remote Sense 0.75Vrms per line Input
Overvoltage Protection Range: 1.4% to 110%
Accuracy: 2% of setpoint
Overcurrent Protection Range: 0.4% to 106%
Accuracy: 3% of setpoint
Auxiliary AC Output Isolated 0Vac to 31.6Vac, 2A max proportional to AC
output
Cooling Forced air convection, req. 40CFM airflow at
altitude and ambient temperature
Multi phase & parallel Up to 6 in a group
Phase Programming Range 0-360 degree; counterclockwise phasor rotation is
assumed, therefore the phase angle offset is lagging
the master reference.
Phase Programming Accuracy 1 degree plus 1°C/kHz for balanced resistive load
measured with respect to A-phase, at 25 degree C,
+/- 5 degree.
Remote programming
connector
9-pin D-sub
Output connector Combination signal/power contact subminiature D
(Mating connector kit available)
Physical

3 RFP™ slots wide 
4.2” (106.7mm) W 
6.75” (171.5mm) H 
15” (381 mm

Weight 13 lbs (5.9 Kilograms)
All specifications: 25°±5°C.
All specifications are subject to change

Manuals
ReFlex Power Operation Manual Rev K - 11/9/2011 (3.64MB)
ReFlex Power Programming Manual Rev J - 11/9/2011 (1.76MB)
Tech Note: Mating Connnectors for Mainframe Rev E - 02/07/09 - 186Kb
Tech Note: Mating Connnectors for Controller Rev F - 02/07/09 - 146Kb
Tech Note: Mating Connnectors for LPDC 16V Rev E - 02/07/09 - 158Kb
Tech Note: Mating Connnectors for LPDC 65V Rev E - 02/07/09 - 153Kb
Tech Note: Mating Connnectors for HPDC 33V / 50V Rev F - 02/07/09 - 94Kb
Tech Note: Mating Connnectors for HPDC 120V Rev X2 - 03/31/09 - 92Kb
Tech Note: Mating Connnectors for HPDC 450V Rev E - 02/07/09 - 108Kb
Tech Note: Mating Connnectors for FPDC Rev E - 02/07/09 - 87Kb
Tech Note: Mating Connnectors for AC Rev D - 02/07/09 - 158Kb
Tech Note: Mating Connnectors for Loads Rev D - 02/07/09 - 99Kb
Tech Note: Fault Protection Groups Rev A - 02/07/09 - 96Kb
Tech Note: Firmware Updates Rev B - 02/07/09 - 421Kb
Quick Reference guide : Reflex Power Network Communication and Output Connections Rev E - 5/6/2010 (244KB)
Data Sheet
ReFlex Power Data Sheet 3/30/2012 (541KB)
Software
AC IVI-COM Driver (2.0.11.0) ¹ 4380277-09 3/26/2012_2.76 Mb
DC IVI-COM Driver (2.0.12.0) ¹ 4380276-10 3/26/2012  3.26 Mb
Loads IVI-COM Driver (2.0.9.0) ¹ 4380278-07 3/26/2012_2.68 Mb
Firmware Update Executable 21.2 Kb
Firmware Update V3.500 2/16/2012 (2.25MB)
ReFlex Power Control & Monitor GUI
- ElgarRAC v2.0.5.0 
- ElgarRDC v2.0.6.0 
- ElgarRLD v2.0.5.0
02/16/2010 - V1.0.0.2 - 33.7Mb
Loading...